diff --git a/configs/olimex-lpc1766stk/README.txt b/configs/olimex-lpc1766stk/README.txt
index 657c46fe5084e0d3b3ba17e2c1cf5519bb27c671..7618766b02c87f1d952256775964d377437a6c29 100755
--- a/configs/olimex-lpc1766stk/README.txt
+++ b/configs/olimex-lpc1766stk/README.txt
@@ -122,6 +122,46 @@ Olimex LPC1766-STK development board
   serial driver).  Other LPC17xx boards with the same clocking will run at
   115200.
 
+  LCD
+  ---
+
+  The LPC1766-STK has a Nokia 6100 132x132 LCD and either a Phillips PCF8833
+  or an Epson S1D15G10 LCD controller.  The NuttX configuration may have to
+  be adjusted depending on which controller is used with the LCD.  The
+  "LPC1766-STK development board Users Manual" states tha the board features
+  a "LCD NOKIA 6610 128x128 x12bit color TFT with Epson LCD controller."
+  But, referring to a different Olimex board, "Nokia 6100 LCD Display
+  Driver," Revision 1, James P. Lynch ("Nokia 6100 LCD Display Driver.pdf")
+  says:
+  
+  "The major irritant in using this display is identifying the graphics
+   controller; there are two possibilities (Epson S1D15G00 or Philips
+   PCF8833). The LCD display sold by the German Web Shop Jelu has a Leadis
+   LDS176 controller but it is 100% compatible with the Philips PCF8833).
+   So how do you tell which controller you have? Some message boards have
+   suggested that the LCD display be disassembled and the controller chip
+   measured with a digital caliper � well that�s getting a bit extreme.
+
+  "Here�s what I know. The Olimex boards have both display controllers
+   possible; if the LCD has a GE-12 sticker on it, it�s a Philips PCF8833.
+   If it has a GE-8 sticker, it�s an Epson controller. The older Sparkfun
+   6100 displays were Epson, their web site indicates that the newer ones
+   are an Epson clone. Sparkfun software examples sometimes refer to the
+   Philips controller so the whole issue has become a bit murky. The
+   trading companies in Honk Kong have no idea what is inside the displays
+   they are selling. A Nokia 6100 display that I purchased from Hong Kong
+   a couple of weeks ago had the Philips controller."
+
+  The LCD connects to the LPC1766 via SPI and two GPIOs.  The two GPIOs are
+  noted above:
+  
+    P1.21 is the SPI chip select, and
+    P3.25 is the LCD reset
+    P3.26 is PWM1 output used to control the backlight intensity.
+  
+  MISO0 and MOSI0 are join via a 1K ohm resistor so the LCD appears to be
+  write only.
+
 Development Environment
 ^^^^^^^^^^^^^^^^^^^^^^^
 
diff --git a/configs/olimex-lpc1766stk/src/lpc1766stk_internal.h b/configs/olimex-lpc1766stk/src/lpc1766stk_internal.h
index b1a461a24d8e71749206548cdd6a61173da45e78..3d84f4bdad64ee92843feee8cb10fde762748e70 100755
--- a/configs/olimex-lpc1766stk/src/lpc1766stk_internal.h
+++ b/configs/olimex-lpc1766stk/src/lpc1766stk_internal.h
@@ -168,7 +168,7 @@
  * P3[26]/STCLK/MAT0[1]/PWM1[3]      26  LCD_BL (PWM1)
  */
 
-#define LPC1766STK_LCD_CS  (GPIO_OUTPUT | GPIO_VALUE_ZERO | GPIO_PORT1 | GPIO_PIN21)
+#define LPC1766STK_LCD_CS  (GPIO_OUTPUT | GPIO_VALUE_ONE | GPIO_PORT1 | GPIO_PIN21)
 #define LPC1766STK_LCD_RST (GPIO_OUTPUT | GPIO_VALUE_ZERO | GPIO_PORT3 | GPIO_PIN25)
 #define LPC1766STK_LCD_BL  GPIO_PWM1p3_3
 #define GPIO_PWM1p3        GPIO_PWM1p3_3
diff --git a/drivers/lcd/nokia6100.c b/drivers/lcd/nokia6100.c
index 36e92007c3135fb4433af29b7fef4bab39aa8d78..008fd297ba5fbf410b55d8b83d4d18601079fca0 100755
--- a/drivers/lcd/nokia6100.c
+++ b/drivers/lcd/nokia6100.c
@@ -474,7 +474,7 @@ static struct nokia_dev_s g_lcddev =
  * P4: 0: Dispersion P40= 1: Non-dispersion
  */
 
-#if CONFIG_NOKIA6100_BPP == 12
+#if 1 // CONFIG_NOKIA6100_BPP == 12
 static const uint8_t g_disctl[] =
 {
   S1D15G10_DISCTL,                  /* Display control */
@@ -543,9 +543,9 @@ static const uint8_t g_datctl[] =
   0,                                /* RGB->RGB */
 #endif
 #if CONFIG_NOKIA6100_BPP == 8
-  DATCTL_16GRAY_A                   /* Selects 16-bit color, Type A */
-#elif CONFIG_NOKIA6100_BPP == 12
   DATCTL_8GRAY                      /* Selects 8-bit color */
+#elif CONFIG_NOKIA6100_BPP == 12
+  DATCTL_16GRAY_A                   /* Selects 16-bit color, Type A */
 #else
 #  error "16-bit mode not yet implemented"
 #endif