#!/bin/bash

LANG=C
ENVBOX=./pybox
DEVICE=/dev/serial/by-id/usb-STMicroelectronics_STM32_Virtual_ComPort_in_FS_Mode_00000000050C-if00
#need sudo apt-get install lm-sensors

reset

VERT="\\033[1;32m"
NORMAL="\\033[0;39m"
ROUGE="\\033[1;31m"
ROSE="\\033[1;35m"
BLEU="\\033[1;34m"
BLANC="\\033[0;02m"
BLANCLAIR="\\033[1;08m"
JAUNE="\\033[1;33m"
CYAN="\\033[1;36m"
echo    ""


echo -e "\t\t---=== System ===---"
echo "[ Software ] :" `$ENVBOX -d $DEVICE SoftwareType` " Rev. " `$ENVBOX -d $DEVICE SoftwareRevision` 
TS=$(echo "`$ENVBOX -d $DEVICE Uptime`/1000" | bc -l )
TSday=$(echo "`$ENVBOX -d $DEVICE Uptime`/86400000 " | bc -l) 
echo "[ Uptime ] : " $(printf "%d" ${TSday/.*}) "day(s)"
echo "[ Uptime ] : " $( date -ud @$TS | awk '{print $4}')
echo "[ Dock ] : " `$ENVBOX -d $DEVICE Switch1 Status`

echo
echo -e "\t\t---=== Power ===---"
echo "[ Voltage ] : " $(printf "%.1f" `$ENVBOX -d $DEVICE LineVoltage`)"V"
echo "[ Current ] : " $(printf "%.1f" `$ENVBOX -d $DEVICE LineCurrent`)"A"
echo
echo -e "\t\t---=== Backlight ===---"
echo
echo "[    Name   ] : " `$ENVBOX -d $DEVICE Backlight1 Name` 
echo "[    Mode   ] : " `$ENVBOX -d $DEVICE Backlight1 Mode` 
echo "[   Enable  ] : " `$ENVBOX -d $DEVICE Backlight1 Enable`
echo "[   Enabled  ] : " `$ENVBOX -d $DEVICE Backlight1 Enabled`
echo "[   Thermal Protection  ] : " `$ENVBOX -d $DEVICE Backlight1 Protection`
echo
echo -e "\t\t---=== Temperatures ===---"
echo "[    Envbox    ] : " $(printf "%.1f" `$ENVBOX -d $DEVICE Temperature1 Temp`)"°C" 
echo "[ T alim1 ] : " $(printf "%.1f" `$ENVBOX -d $DEVICE Temperature2 Temp`)"°C"
echo "[ T alim2  ] : " $(printf "%.1f" `$ENVBOX -d $DEVICE Temperature3 Temp`)"°C"
echo
echo "[ T upscale  ] : " $(printf "%.1f" `$ENVBOX -d $DEVICE Temperature5 Temp`)"°C"
echo
echo -e "\t\t---=== FAN A ===---"
echo "[   Mode   ] : " `$ENVBOX -d $DEVICE Fan1 Mode` 
echo "[  Command ] : " $(printf "%.1f" `$ENVBOX -d $DEVICE Fan1 PWM`)"%"
echo "[  Tachy   ] : " $(printf "%.1f" `$ENVBOX -d $DEVICE Fan1 RPM`)"rpm"
echo -e "\t\t---=== FAN B ===---"
echo
echo "[   Mode   ] : " `$ENVBOX -d $DEVICE Fan2 Mode` 
echo "[  Command ] : " $(printf "%.1f" `$ENVBOX -d $DEVICE Fan2 PWM`)"%"
echo "[   Tachy  ] : " $(printf "%.1f" `$ENVBOX -d $DEVICE Fan2 RPM`)"rpm"