- Apr 04, 2014
-
-
nothinman authored
Update Readme descriptions for M200, M207 and M208
-
whosawhatsis authored
-
nothinman authored
FWRETRACT in mm/s
-
- Apr 03, 2014
-
-
nothinman authored
Change CONTROLLERFAN_PIN for board 35 to -1, as it would conflict with board's 33 extruder pin, causing burnout (it's the same board, just different number of fans/extruders, therefore should be pin-compatible)
-
- Apr 02, 2014
- Apr 01, 2014
-
-
Tim authored
some guy find that marlin not working good for dual extruders delta . when type T0 or T1 to active extruder and E0 or E1 move causing XYZ motion . so i locales the bugs and fix it , I have dry run the fix.
-
- Mar 30, 2014
-
-
whosawhatsis authored
-
whosawhatsis authored
-
- Mar 27, 2014
-
-
David Forrest authored
-
- Mar 19, 2014
-
-
nothinman authored
Extended Preheat options
-
Dim3nsioneer authored
-
Dim3nsioneer authored
-
Dim3nsioneer authored
-
- Mar 17, 2014
-
-
Dim3nsioneer authored
Preheat LCD menus base on code by D-Base
-
- Mar 15, 2014
-
-
ErikZalm authored
Set flow rate (extrude-mutliplier) for each extruder individually
-
Dim3nsioneer authored
Extension of M221, Tune menu
-
Dim3nsioneer authored
Update on 140315
-
ErikZalm authored
Add support for disabling encoder control for feedrate multiplier
-
ErikZalm authored
Added CHDK support
-
- Mar 14, 2014
-
-
whosawhatsis authored
Firmware retraction now stores the retract and recover speeds in mm/s instead of mm/min. This makes it match the units of the maximum feedrate, and fixes problems with modifying the value via LCD control panel. From gcode, the values are still taken in mm/min to match the units of G1 and similar, and they are converted to mm/s before they are stored. I also lowered the default retract feedrate to make it less likely to cause problems for geared extruders when the user hasn’t bothered to set a reasonable maximum feedrate, though users should be setting both of these values to suit their hardware.
-
- Mar 12, 2014
-
-
Matthew Schick authored
Signed-off-by: Matthew Schick <matthew.schick@gmail.com>
-
- Mar 10, 2014
-
-
blddk authored
Added CHDK support to take pictures instead of doing an IR command, see more about how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
-
blddk authored
Added so M240 can be used to trigger CHDK instead of sending an IR signal, see more about CHDK here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
-
- Mar 05, 2014
-
-
nothinman authored
Fixed Finnish translation
-
Tommi Lamberg authored
- Fixed Few finnish transalations - Removed duplicate contrast define
-
- Feb 26, 2014
-
-
ErikZalm authored
temperature.cpp: Fix PID_DEBUG compile error.
-
ErikZalm authored
Update README.md with Autotemp typo fix
-
Erik van der Zalm authored
-
ErikZalm authored
Add M665 to dynamically set delta configuration
-
Jim Morris authored
Conflicts: Marlin/Marlin_main.cpp
-
David Forrest authored
-
- Feb 25, 2014
-
-
anfroholic authored
-
ErikZalm authored
Various typo fixes #5 - only in comments, no code changes.
-
ErikZalm authored
Various typo fixes #4 - only in comments, no code changes.
-
Cylindric authored
-
Cylindric authored
-
- Feb 24, 2014