hn70ap_spi.c

/*******************************************************************************
 * configs/hn70ap/src/stm32_spi.c
 *
 *   Copyright (C) 2011-2012 Gregory Nutt. All rights reserved.
 *   Authors: Gregory Nutt <gnutt@nuttx.org>
 *            Marco Krahl <ocram.lhark@gmail.com>
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in
 *    the documentation and/or other materials provided with the
 *    distribution.
 * 3. Neither the name NuttX nor the names of its contributors may be
 *    used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
 * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
 * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
 * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
 * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 ******************************************************************************/

/*******************************************************************************
 * Included Files
 ******************************************************************************/

#include <nuttx/config.h>

#include <stdint.h>
#include <stdbool.h>
#include <errno.h>
#include <debug.h>

#include <nuttx/spi/spi.h>
#include <arch/board/board.h>

#include "up_arch.h"
#include "chip.h"
#include "stm32.h"
#include "hn70ap.h"

/*******************************************************************************
 * Private Data
 ******************************************************************************/

/*******************************************************************************
 * Public Functions
 ******************************************************************************/

/*******************************************************************************
 * Name: stm32_spidev_initialize
 *
 * Description:
 *   Called to configure SPI chip select GPIO pins for the hn70ap board.
 *
 ******************************************************************************/

void hn70ap_spi_initialize(void)
{
#if defined(CONFIG_STM32_SPI2) && defined(CONFIG_MTD_SST26)
  stm32_configgpio(GPIO_CS_SST26);   /* SST26 FLASH chip select */
#endif

#if defined(CONFIG_STM32_SPI4) && defined(CONFIG_DRIVERS_GENERICRADIO)
  stm32_configgpio(GPIO_CS_RADIOMAIN);  /* On-board si4463 */
  stm32_configgpio(GPIO_CS_RADIOAUX);   /* Radio module */
#endif
}

/****************************************************************************
 * Name:  stm32_spi1/2/3/4/5select and stm32_spi1/2/3/4/5status
 *
 * Description:
 *   The external functions, stm32_spi1/2/3select and stm32_spi1/2/3status must
 *   be provided by board-specific logic.  They are implementations of the
 *   select and status methods of the SPI interface defined by struct spi_ops_s
 *   (see include/nuttx/spi/spi.h). All other methods (including
 *   stm32_spibus_initialize()) are provided by common STM32 logic.
 *   To use this common SPI logic on your board:
 *
 *   1. Provide logic in stm32_boardinitialize() to configure SPI chip select
 *      pins.
 *   2. Provide stm32_spi1/2/3select() and stm32_spi1/2/3status() functions in
 *      your board-specific logic.  These functions will perform chip selection
 *      and status operations using GPIOs in the way your board is configured.
 *   3. Add a calls to stm32_spibus_initialize() in your low level application
 *      initialization logic
 *   4. The handle returned by stm32_spibus_initialize() may then be used to
 *      bind the SPI driver to higher level logic (e.g., calling
 *      mmcsd_spislotinitialize(), for example, will bind the SPI driver to
 *      the SPI MMC/SD driver).
 *
 ****************************************************************************/

#ifdef CONFIG_STM32_SPI2
void stm32_spi2select(FAR struct spi_dev_s *dev, uint32_t devid, bool selected)
{
//  spiinfo("devid: %d CS: %s\n", (int)devid, selected ? "assert" : "de-assert");
#if defined(CONFIG_MTD_SST26)
  if (devid == SPIDEV_FLASH(0))
    {
      stm32_gpiowrite(GPIO_CS_SST26, !selected);
    }
#endif
}

uint8_t stm32_spi2status(FAR struct spi_dev_s *dev, uint32_t devid)
{
  return 0;
}
#endif

#ifdef CONFIG_STM32_SPI4
void stm32_spi4select(FAR struct spi_dev_s *dev, uint32_t devid, bool selected)
{
//  spiinfo("devid: %08X CS: %s\n", devid, selected ? "assert" : "de-assert");  
#ifdef CONFIG_DRIVERS_GENERICRADIO
  if (devid == SPIDEV_GENRADIO(0))
    {
      stm32_gpiowrite(GPIO_CS_RADIOMAIN, !selected);
    }
  else if (devid == SPIDEV_GENRADIO(1))
    {
      stm32_gpiowrite(GPIO_CS_RADIOAUX, !selected);
    }
#endif
}

uint8_t stm32_spi4status(FAR struct spi_dev_s *dev, uint32_t devid)
{
  return 0;
}
#endif


/****************************************************************************
 * Name: stm32_spi1cmddata
 *
 * Description:
 *   Set or clear the SH1101A A0 or SD1306 D/C n bit to select data (true)
 *   or command (false). This function must be provided by platform-specific
 *   logic. This is an implementation of the cmddata method of the SPI
 *   interface defined by struct spi_ops_s (see include/nuttx/spi/spi.h).
 *
 * Input Parameters:
 *
 *   spi - SPI device that controls the bus the device that requires the CMD/
 *         DATA selection.
 *   devid - If there are multiple devices on the bus, this selects which one
 *         to select cmd or data.  NOTE:  This design restricts, for example,
 *         one one SPI display per SPI bus.
 *   cmd - true: select command; false: select data
 *
 * Returned Value:
 *   None
 *
 ****************************************************************************/

#ifdef CONFIG_SPI_CMDDATA

#ifdef CONFIG_STM32_SPI2
int stm32_spi2cmddata(FAR struct spi_dev_s *dev, uint32_t devid, bool cmd)
{
  return -ENODEV;
}
#endif

#ifdef CONFIG_STM32_SPI4
int stm32_spi4cmddata(FAR struct spi_dev_s *dev, uint32_t devid, bool cmd)
{
  return -ENODEV;
}
#endif

#endif /* CONFIG_SPI_CMDDATA */