Newer
Older
README for NuttX port to the Embedded Artists' base board with the NXP
the LPCXpresso daughter board.
Contents
^^^^^^^^
LCPXpresso LPC1768 Board
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
Development Environment
GNU Toolchain Options
NuttX buildroot Toolchain
Code Red IDE
LEDs
LPCXpresso Configuration Options
Configurations
LCPXpresso LPC1768 Board
^^^^^^^^^^^^^^^^^^^^^^^^
Pin Description Connector On Board Base Board
-------------------------------- --------- -------------- ---------------------
P0[0]/RD1/TXD3/SDA1 J6-9 I2C E2PROM SDA TXD3/SDA1
P0[1]/TD1/RXD3/SCL J6-10 RXD3/SCL1
P0[2]/TXD0/AD0[7] J6-21
P0[3]/RXD0/AD0[6] J6-22
P0[4]/I2SRX-CLK/RD2/CAP2.0 J6-38 CAN_RX2
P0[5]/I2SRX-WS/TD2/CAP2.1 J6-39 CAN_TX2
P0[6]/I2SRX_SDA/SSEL1/MAT2[0] J6-8 SSEL1
P0[7]/I2STX_CLK/SCK1/MAT2[1] J6-7 SCK1
P0[8]/I2STX_WS/MISO1/MAT2[2] J6-6 MISO1
P0[9]/I2STX_SDA/MOSI1/MAT2[3] J6-5 MOSI1
P0[10] J6-40 TXD2/SDA2
P0[11] J6-41 RXD2/SCL2
P0[15]/TXD1/SCK0/SCK J6-13 TXD1/SCK0
P0[16]/RXD1/SSEL0/SSEL J6-14 RXD1/SSEL0
P0[17]/CTS1/MISO0/MISO J6-12 MISO0
P0[18]/DCD1/MOSI0/MOSI J6-11 MOSI0
P0[19]/DSR1/SDA1 PAD17 N/A
P0[20]/DTR1/SCL1 PAD18 I2C E2PROM SCL N/A
P0[21]/RI1/MCIPWR/RD1 J6-23
P0[22]/RTS1/TD1 J6-24 LED
P0[23]/AD0[0]/I2SRX_CLK/CAP3[0] J6-15 AD0.0
P0[24]/AD0[1]/I2SRX_WS/CAP3[1] J6-16 AD0.1
P0[25]/AD0[2]/I2SRX_SDA/TXD3 J6-17 AD0.2
P0[26]/AD0[3]/AOUT/RXD3 J6-18 AD0.3/AOUT / RGB LED
P0[27]/SDA0/USB_SDA J6-25
P0[28]/SCL0 J6-26
P0[29]/USB_D+ J6-37 USB_D+
P0[30]/USB_D- J6-36 USB_D-
P1[0]/ENET-TXD0 J6-34? TXD0 TX-(Ethernet PHY)
P1[1]/ENET_TXD1 J6-35? TXD1 TX+(Ethernet PHY)
P1[4]/ENET_TX_EN TXEN N/A
P1[8]/ENET_CRS CRS_DV/MODE2 N/A
P1[9]/ENET_RXD0 J6-32? RXD0/MODE0 RD-(Ethernet PHY)
P1[10]/ENET_RXD1 J6-33? RXD1/MODE1 RD+(Ethernet PHY)
P1[14]/ENET_RX_ER RXER/PHYAD0 N/A
P1[15]/ENET_REF_CLK REFCLK N/A
P1[16]/ENET_MDC MDC N/A
P1[17]/ENET_MDIO MDIO N/A
P1[18]/USB_UP_LED/PWM1[1]/CAP1[0] PAD1 N/A
P1[19]/MC0A/USB_PPWR/N_CAP1.1 PAD2 N/A
P1[20]/MCFB0/PWM1.2/SCK0 PAD3 N/A
P1[21]/MCABORT/PWM1.3/SSEL0 PAD4 N/A
P1[22]/MC0B/USB-PWRD/MAT1.0 PAD5 N/A
P1[23]/MCFB1/PWM1.4/MISO0 PAD6 N/A
P1[24]/MCFB2/PWM1.5/MOSI0 PAD7 N/A
P1[25]/MC1A/MAT1.1 PAD8 N/A
P1[26]/MC1B/PWM1.6/CAP0.0 PAD9 N/A
P1[27]/CLKOUT/USB-OVRCR-N/CAP0.1 PAD10 N/A
P1[28]/MC2A/PCAP1.0/MAT0.0 PAD11 N/A
P1[29]/MC2B/PCAP1.1/MAT0.1 PAD12 N/A
P1[30]/VBUS/AD0[4] J6-19 AD0.4
P1[31]/SCK1/AD0[5] J6-20 AD0.5
P2[0]/PWM1.1/TXD1 J6-42 PWM1.1 / RGB LED / RS422 RX
P2[1]/PWM1.2/RXD1 J6-43 PWM1.2 / OLED voltage / RGB LED
P2[2]/PWM1.3/CTS1/TRACEDATA[3] J6-44 PWM1.3
P2[3]/PWM1.4/DCD1/TRACEDATA[2] J6-45 PWM1.4
P2[4]/PWM1.5/DSR1/TRACEDATA[1] J6-46 PWM1.5
P2[5]/PWM1[6]/DTR1/TRACEDATA[0] J6-47 PWM1.6
P2[6]/PCAP1[0]/RI1/TRACECLK J6-48
P2[7]/RD2/RTS1 J6-49
P2[8]/TD2/TXD2 J6-50
P2[9]/USB_CONNECT/RXD2 PAD19 USB Pullup N/A
P2[10]/EINT0/NMI J6-51
P2[11]/EINT1/I2STX_CLK J6-52
P2[12]/EINT2/I2STX_WS j6-53
P2[13]/EINT3/I2STX_SDA J6-27
P3[25]/MAT0.0/PWM1.2 PAD13 N/A
P3[26]/STCLK/MAT0.1/PWM1.3 PAD14 N/A
P4[28]/RX-MCLK/MAT2.0/TXD3 PAD15 N/A
P4[29]/TX-MCLK/MAT2.1/RXD3 PAD16 N/A
Embedded Artist's Base Board
^^^^^^^^^^^^^^^^^^^^^^^^^^^^
There are many jumpers on the base board. A usable combination is the
default jumper settings WITH the two J54 jumpers both removed. Those
jumpers are for ISP support and will cause the board to reset.
To use the SD, J55 must be set to provide chip select PIO1_11 signal as
the SD slot chip select.
SD Slot
-------
Base-board J4/J6 LPC1768
SD Signal Pin Pin
--- ----------- ----- --------
CS PIO1_11* 55 P2.2
DIN PIO0_9-MOSI 5 P0.9 MOSI1
DOUT PIO0_8-MISO 6 P0.8 MISO1
CLK PIO2_11-SCK 7 P0.9 SCK1
CD PIO2_10 52 P2.11
*J55 must be set to provide chip select PIO1_11 signal as the SD slot
chip select.
Base-board J4/J6 LPC1768
Signal Pin Pin
------------------- ----- --------
PIO0_6-USB_CONNECT* 23 P0.21
USB_DM 36 USB_D-
USB_DP 37 USB_D+
PIO0_3-VBUS_SENSE 39 P0.5
*J14 must be set to permit GPIO control of the USB connect pin
J23 is associated the LEDs used for USB support
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
Development Environment
^^^^^^^^^^^^^^^^^^^^^^^
Either Linux or Cygwin on Windows can be used for the development environment.
The source has been built only using the GNU toolchain (see below). Other
toolchains will likely cause problems. Testing was performed using the Cygwin
environment.
GNU Toolchain Options
^^^^^^^^^^^^^^^^^^^^^
The NuttX make system has been modified to support the following different
toolchain options.
1. The CodeSourcery GNU toolchain,
2. The devkitARM GNU toolchain,
3. The NuttX buildroot Toolchain (see below).
All testing has been conducted using the NuttX buildroot toolchain. However,
the make system is setup to default to use the devkitARM toolchain. To use
the CodeSourcery or devkitARM toolchain, you simply need add one of the
following configuration options to your .config (or defconfig) file:
CONFIG_LPC17_CODESOURCERYW=y : CodeSourcery under Windows
CONFIG_LPC17_CODESOURCERYL=y : CodeSourcery under Linux
CONFIG_LPC17_DEVKITARM=y : devkitARM under Windows
CONFIG_LPC17_BUILDROOT=y : NuttX buildroot under Linux or Cygwin (default)
If you are not using CONFIG_LPC17_BUILDROOT, then you may also have to modify
the PATH in the setenv.h file if your make cannot find the tools.
NOTE: the CodeSourcery (for Windows)and devkitARM are Windows native toolchains.
The CodeSourcey (for Linux) and NuttX buildroot toolchains are Cygwin and/or
Linux native toolchains. There are several limitations to using a Windows based
toolchain in a Cygwin environment. The three biggest are:
1. The Windows toolchain cannot follow Cygwin paths. Path conversions are
performed automatically in the Cygwin makefiles using the 'cygpath' utility
but you might easily find some new path problems. If so, check out 'cygpath -w'
2. Windows toolchains cannot follow Cygwin symbolic links. Many symbolic links
are used in Nuttx (e.g., include/arch). The make system works around these
problems for the Windows tools by copying directories instead of linking them.
But this can also cause some confusion for you: For example, you may edit
a file in a "linked" directory and find that your changes had not effect.
That is because you are building the copy of the file in the "fake" symbolic
directory. If you use a Windows toolchain, you should get in the habit of
making like this:
make clean_context all
An alias in your .bashrc file might make that less painful.
3. Dependencies are not made when using Windows versions of the GCC. This is
because the dependencies are generated using Windows pathes which do not
work with the Cygwin make.
Support has been added for making dependencies with the windows-native toolchains.
That support can be enabled by modifying your Make.defs file as follows:
- MKDEP = $(TOPDIR)/tools/mknulldeps.sh
+ MKDEP = $(TOPDIR)/tools/mkdeps.sh --winpaths "$(TOPDIR)"
If you have problems with the dependency build (for example, if you are not
building on C:), then you may need to modify tools/mkdeps.sh
NOTE 1: The CodeSourcery toolchain (2009q1) does not work with default optimization
level of -Os (See Make.defs). It will work with -O0, -O1, or -O2, but not with
-Os.
NOTE 2: The devkitARM toolchain includes a version of MSYS make. Make sure that
the paths to Cygwin's /bin and /usr/bin directories appear BEFORE the devkitARM
path or will get the wrong version of make.
Code Red IDE
^^^^^^^^^^^^
NuttX is built using command-line make. It can be used with an IDE, but some
effort will be required to create the project (There is a simple RIDE project
in the RIDE subdirectory).
Makefile Build
--------------
Under Eclipse, it is pretty easy to set up an "empty makefile project" and
simply use the NuttX makefile to build the system. That is almost for free
under Linux. Under Windows, you will need to set up the "Cygwin GCC" empty
makefile project in order to work with Windows (Google for "Eclipse Cygwin" -
there is a lot of help on the internet).
Native Build
------------
Here are a few tips before you start that effort:
1) Select the toolchain that you will be using in your .config file
2) Start the NuttX build at least one time from the Cygwin command line
before trying to create your project. This is necessary to create
certain auto-generated files and directories that will be needed.
3) Set up include pathes: You will need include/, arch/arm/src/lpc17xx,
arch/arm/src/common, arch/arm/src/cortexm3, and sched/.
4) All assembly files need to have the definition option -D __ASSEMBLY__
on the command line.
Startup files will probably cause you some headaches. The NuttX startup file
is arch/arm/src/lpc17x/lpc17_vectors.S.
Using Code Red GNU Tools from Cygwin
------------------------------------
Under Cygwin, the Code Red command line tools (e.g., arm-non-eabi-gcc) cannot
be executed because the they only have execut privileges for Administrators. I
worked around this by:
Opening a native Cygwin RXVT as Administrator (Right click, "Run as administrator"),
then executing 'chmod 755 *.exe' in the following directories:
/cygdrive/c/nxp/lpcxpreeso_3.6/bin, and
/cygdrive/c/nxp/lpcxpreeso_3.6/Tools/bin
Command Line Flash Programming
------------------------------
If using LPCLink as your debug connection, first of all boot the LPC-Link using
the script:
bin\Scripts\bootLPCXpresso type
where type = winusb for Windows XP, or type = hid for Windows Vista / 7.
Now run the flash programming utility with the following options
flash_utility wire -ptarget -flash-load[-exec]=filename [-load-base=base_address]
Where flash_utility is one of:
crt_emu_lpc11_13 (for LPC11xx or LPC13xx parts)
crt_emu_cm3_nxp (for LPC17xx parts)
crt_emu_a7_nxp (for LPC21/22/23/24 parts)
crt_emu_a9_nxp (for LPC31/32 and LPC29xx parts)
crt_emu_cm3_lmi (for TI Stellaris LM3S parts
wire is one of:
(empty) (for Red Probe+, Red Probe, RDB1768v1, or TI Stellaris evaluation boards)
-wire=hid (for RDB1768v2 without upgraded firmware)
-wire=winusb (for RDB1768v2 with upgraded firmware)
-wire=winusb (for LPC-Link on Windows XP)
-wire=hid (for LPC-Link on Windows Vista/ Windows 7)
target is the target chip name. For example LPC1343, LPC1114/301, LPC1768 etc.
filename is the file to flash program. It may be an executable (axf) or a binary
(bin) file. If using a binary file, the base_address must be specified.
base_address is the base load address when flash programming a binary file. It
should be specified as a hex value with a leading 0x.
Note:
- flash-load will leave the processor in a stopped state
- flash-load-exec will start execution of application as soon as download has
completed.
Examples
To load the executable file app.axf and start it executing on an LPC1758
target using Red Probe, use the following command line:
crt_emu_cm3_nxp -pLPC1758 -flash-load-exec=app.axf
To load the binary file binary.bin to address 0x1000 to an LPC1343 target
using LPC-Link on Windows XP, use the following command line:
crt_emu_lpc11_13_nxp -wire=hid -pLPC1343 -flash-load=binary.bin -load-base=0x1000
NuttX buildroot Toolchain
^^^^^^^^^^^^^^^^^^^^^^^^^
A GNU GCC-based toolchain is assumed. The files */setenv.sh should
be modified to point to the correct path to the Cortex-M3 GCC toolchain (if
different from the default in your PATH variable).
If you have no Cortex-M3 toolchain, one can be downloaded from the NuttX
SourceForge download site (https://sourceforge.net/project/showfiles.php?group_id=189573).
This GNU toolchain builds and executes in the Linux or Cygwin environment.
1. You must have already configured Nuttx in <some-dir>/nuttx.
cd tools
./configure.sh lpcxpresso-lpc1768/<sub-dir>
2. Download the latest buildroot package into <some-dir>
3. unpack the buildroot tarball. The resulting directory may
have versioning information on it like buildroot-x.y.z. If so,
rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.
4. cd <some-dir>/buildroot
5. cp configs/cortexm3-defconfig-4.3.3 .config
6. make oldconfig
7. make
8. Edit setenv.h, if necessary, so that the PATH variable includes
the path to the newly built binaries.
See the file configs/README.txt in the buildroot source tree. That has more
detailed PLUS some special instructions that you will need to follow if you
are building a Cortex-M3 toolchain for Cygwin under Windows.
NOTE: This is an OABI toolchain.
LEDs
^^^^
If CONFIG_ARCH_LEDS is defined, then support for the LPCXpresso LEDs will be
included in the build. See:
- configs/lpcxpresso-lpc1768/include/board.h - Defines LED constants, types and
prototypes the LED interface functions.
- configs/lpcxpresso-lpc1768/src/lpcxpresso_internal.h - GPIO settings for the LEDs.
- configs/lpcxpresso-lpc1768/src/up_leds.c - LED control logic.
The LPCXpresso LPC1768 has a single LEDs (there are more on the Embedded Artists
base board, but those are not controlled by NuttX). Usage this single LED by NuttX
is as follows:
- The LED is not illuminated until the LPCXpresso completes initialization.
If the LED is stuck in the OFF state, this means that the LPCXpresso did not
complete intialization.
- Each time the OS enters an interrupt (or a signal) it will turn the LED OFF and
restores its previous stated upon return from the interrupt (or signal).
The normal state, after initialization will be a dull glow. The brightness of
the glow will be inversely related to the proportion of time spent within interrupt
handling logic. The glow may decrease in brightness when the system is very
busy handling device interrupts and increase in brightness as the system becomes
idle.
Stuck in the OFF state suggests that that the system never completed
initialization; Stuck in the ON state would indicated that the system
intialialized, but is not takint interrupts.
- If a fatal assertion or a fatal unhandled exception occurs, the LED will flash
strongly as a slow, 1Hz rate.
LPCXpresso Configuration Options
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
be set to:
CONFIG_ARCH=arm
CONFIG_ARCH_family - For use in C code:
CONFIG_ARCH_ARM=y
CONFIG_ARCH_architecture - For use in C code:
CONFIG_ARCH_CORTEXM3=y
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
CONFIG_ARCH_CHIP=lpc17xx
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
chip:
CONFIG_ARCH_CHIP_LPC1768=y
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
hence, the board that supports the particular chip or SoC.
CONFIG_ARCH_BOARD=lpcxpresso-lpc1768
CONFIG_ARCH_BOARD_name - For use in C code
CONFIG_ARCH_BOARD_LPCEXPRESSO=y
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
of delay loops
CONFIG_ENDIAN_BIG - define if big endian (default is little
endian)
CONFIG_DRAM_SIZE - Describes the installed DRAM (CPU SRAM in this case):
CONFIG_DRAM_SIZE=(32*1024) (32Kb)
There is an additional 32Kb of SRAM in AHB SRAM banks 0 and 1.
CONFIG_DRAM_START - The start address of installed DRAM
CONFIG_DRAM_START=0x10000000
CONFIG_DRAM_END - Last address+1 of installed RAM
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
CONFIG_ARCH_IRQPRIO - The LPC17xx supports interrupt prioritization
CONFIG_ARCH_IRQPRIO=y
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
have LEDs
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
stack. If defined, this symbol is the size of the interrupt
stack in bytes. If not defined, the user task stacks will be
used during interrupt handling.
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
cause a 100 second delay during boot-up. This 100 second delay
serves no purpose other than it allows you to calibratre
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
the delay actually is 100 seconds.
Individual subsystems can be enabled:
CONFIG_LPC17_MAINOSC=y
CONFIG_LPC17_PLL0=y
CONFIG_LPC17_PLL1=n
CONFIG_LPC17_ETHERNET=n
CONFIG_LPC17_USBHOST=n
CONFIG_LPC17_USBOTG=n
CONFIG_LPC17_USBDEV=n
CONFIG_LPC17_UART0=y
CONFIG_LPC17_UART1=n
CONFIG_LPC17_UART2=n
CONFIG_LPC17_UART3=n
CONFIG_LPC17_CAN1=n
CONFIG_LPC17_CAN2=n
CONFIG_LPC17_SPI=n
CONFIG_LPC17_SSP0=n
CONFIG_LPC17_SSP1=n
CONFIG_LPC17_I2C0=n
CONFIG_LPC17_I2C1=n
CONFIG_LPC17_I2S=n
CONFIG_LPC17_TMR0=n
CONFIG_LPC17_TMR1=n
CONFIG_LPC17_TMR2=n
CONFIG_LPC17_TMR3=n
CONFIG_LPC17_RIT=n
CONFIG_LPC17_PWM=n
CONFIG_LPC17_MCPWM=n
CONFIG_LPC17_QEI=n
CONFIG_LPC17_RTC=n
CONFIG_LPC17_WDT=n
CONFIG_LPC17_ADC=n
CONFIG_LPC17_DAC=n
CONFIG_LPC17_GPDMA=n
CONFIG_LPC17_FLASH=n
LPC17xx specific device driver settings
CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
console and ttys0 (default is the UART0).
CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
This specific the size of the receive buffer
CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
being sent. This specific the size of the transmit buffer
CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
CONFIG_UARTn_2STOP - Two stop bits
LPC17xx specific PHY/Ethernet device driver settings. These setting
also require CONFIG_NET and CONFIG_LPC17_ETHERNET.
CONFIG_PHY_KS8721 - Selects Micrel KS8721 PHY
CONFIG_PHY_AUTONEG - Enable auto-negotion
CONFIG_PHY_SPEED100 - Select 100Mbit vs. 10Mbit speed.
CONFIG_PHY_FDUPLEX - Select full (vs. half) duplex
CONFIG_NET_EMACRAM_SIZE - Size of EMAC RAM. Default: 16Kb
CONFIG_NET_NTXDESC - Configured number of Tx descriptors. Default: 18
CONFIG_NET_NRXDESC - Configured number of Rx descriptors. Default: 18
CONFIG_NET_PRIORITY - Ethernet interrupt priority. The is default is
the higest priority.
CONFIG_NET_WOL - Enable Wake-up on Lan (not fully implemented).
CONFIG_NET_REGDEBUG - Enabled low level register debug. Also needs
CONFIG_DEBUG.
CONFIG_NET_DUMPPACKET - Dump all received and transmitted packets.
Also needs CONFIG_DEBUG.
CONFIG_NET_HASH - Enable receipt of near-perfect match frames.
CONFIG_NET_MULTICAST - Enable receipt of multicast (and unicast) frames.
Automatically set if CONFIG_NET_IGMP is selected.
LPC17xx USB Device Configuration
CONFIG_LPC17_USBDEV_FRAME_INTERRUPT
Handle USB Start-Of-Frame events.
Enable reading SOF from interrupt handler vs. simply reading on demand.
Probably a bad idea... Unless there is some issue with sampling the SOF
from hardware asynchronously.
CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT
Enable high priority interrupts. I have no idea why you might want to
do that
CONFIG_LPC17_USBDEV_NDMADESCRIPTORS
Number of DMA descriptors to allocate in SRAM.
CONFIG_LPC17_USBDEV_DMA
Enable lpc17xx-specific DMA support
LPC17xx USB Host Configuration (the LPCXpresso does not support USB Host)
CONFIG_USBHOST_OHCIRAM_SIZE
Total size of OHCI RAM (in AHB SRAM Bank 1)
CONFIG_USBHOST_NEDS
Number of endpoint descriptors
CONFIG_USBHOST_NTDS
Number of transfer descriptors
CONFIG_USBHOST_TDBUFFERS
Number of transfer descriptor buffers
CONFIG_USBHOST_TDBUFSIZE
Size of one transfer descriptor buffer
CONFIG_USBHOST_IOBUFSIZE
Size of one end-user I/O buffer. This can be zero if the
application can guarantee that all end-user I/O buffers
reside in AHB SRAM.
Configurations
^^^^^^^^^^^^^^
Each LPCXpresso configuration is maintained in a sudirectory and can be
selected as follow:
cd tools
./configure.sh lpcxpresso-lpc1768/<subdir>
cd -
. ./setenv.sh
Where <subdir> is one of the following:
nsh:
Configures the NuttShell (nsh) located at apps/examples/nsh. The
Configuration enables both the serial and telnet NSH interfaces.
Support for the board's SPI-based MicroSD card is included
(but not passing tests as of this writing).
ostest:
This configuration directory, performs a simple OS test using
NOTE: The OSTest runs on the LPCXpresso if it is not installed
on the base board (using an add-on MAX232 RS232 driver connected
to:
P0[0]/RD1/TXD3/SDA1 J6-9
P0[1]/TD1/RXD3/SCL J6-10
I suspect that this test does not run on with the base board
attached because OSTest blasts out a lot of serial data and
overruns the FTDI chip before it has a chance to establish the
connection with the host.
thttpd:
This builds the THTTPD web server example using the THTTPD and
the apps/examples/thttpd application.
usbstorage:
This configuration directory exercises the USB mass storage
class driver at apps/examples/usbstorage. See apps/examples/README.txt
for more information.