Something went wrong on our end
-
patacongo authored
git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@704 42af7a65-404d-4744-a932-0658087f49c3
patacongo authoredgit-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@704 42af7a65-404d-4744-a932-0658087f49c3
chip.h 8.69 KiB
/************************************************************************************
* arch/z80/src/z8/chip.h
* arch/z80/src/chip/chip.h
*
* Copyright (C) 2008 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <spudmonkey@racsa.co.cr>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __Z8_CHIP_H
#define __Z8_CHIP_H
/************************************************************************************
* Included Files
************************************************************************************/
/************************************************************************************
* Definitions
************************************************************************************/
/* Hexadecimal Representation *******************************************************/
#ifdef __ASSEMBLY__
# define _HX(h) %##h
#else
# define _HX(h) 0x##h
#endif
/* Memory Map
*
* 64Kb Program Memory (64K series)
* C:0000 - C:0001 : Flash options
* C:0002 - C:0037 : Vectors
* : ROM data
* : Code
*
* 4Kb Register File (64K series)
* R:020 - R:0ff : 224 byte RDATA
* R:0e0 - R:0ef : 16-byte working register area (RDATA)
* E:100 - E:eff : 3.5 Kbyte EDATA
* f00 - fff : 256 byte control register area
*/
/* Special Function Registers *******************************************************
*
* Because of the many different ez80 configurations, we will rely on the
* ZDS-II header file, ez8.h, to provide the correct addresses for each register.
*/
/* Timer Register Bit Definitions ***************************************************/
/* Timer control register */
#define Z8_TIMERCTL_TEN _HX(80) /* Bit 7: Timer enabled */
#define Z8_TIMERCTL_TPOL _HX(40) /* Bit 6: Timer input/output polarity */
#define Z8_TIMERCTL_DIV1 _HX(00) /* Bits 3-5: Pre-scale divisor */
#define Z8_TIMERCTL_DIV2 _HX(08)
#define Z8_TIMERCTL_DIV4 _HX(10)
#define Z8_TIMERCTL_DIV8 _HX(18)
#define Z8_TIMERCTL_DIV16 _HX(20)
#define Z8_TIMERCTL_DIV32 _HX(28)
#define Z8_TIMERCTL_DIV64 _HX(30)
#define Z8_TIMERCTL_DIV128 _HX(38)
#define Z8_TIMERCTL_ONESHOT _HX(00) /* Bits 0-2: Timer mode */
#define Z8_TIMERCTL_CONT _HX(01)
#define Z8_TIMERCTL_COUNTER _HX(02)
#define Z8_TIMERCTL_PWM _HX(03)
#define Z8_TIMERCTL_CAPTURE _HX(04)
#define Z8_TIMERCTL_COMPARE _HX(05)
#define Z8_TIMERCTL_GATED _HX(06)
#define Z8_TIMERCTL_CAPCMP _HX(07)
/* UART Register Offsets *************************************************************/
#define Z8_UART_TXD _HX(00) /* 8-bits: UART Transmit Data */
#define Z8_UART_RXD _HX(00) /* 8-bits: UART Receive Data */
#define Z8_UART_STAT0 _HX(01) /* 8-bits: UART Status 0 */
#define Z8_UART_CTL _HX(02) /* 16-bits: UART Control */
#define Z8_UART_CTL0 _HX(02) /* 8-bits: UART Control 0 */
#define Z8_UART_CTL1 _HX(03) /* 8-bits: UART COntrol 1 */
#if defined(_Z8FMC16) || defined(_Z8F1680)
# define Z8_UART_MDSTAT _HX(04) /* 8-bits: UART Mode Select & Status */
#else
# define Z8_UART_STAT1 _HX(04) /* 8-bits: UART Status 1 */
#endif
#define Z8_UART_ADDR _HX(05) /* 8-bits: UART Address Compare */
#define Z8_UART_BR _HX(06) /* 16-bits: UART Baud Rate */
#define Z8_UART_BRH _HX(06) /* 8-bits: UART Baud Rate High Byte */
#define Z8_UART_BRL _HX(07) /* 8-bits: UART Baud Rate Low Byte */
/* UART0/1 Base Register Addresses **************************************************/
#ifdef EZ8_UART0
# define Z8_UART0_BASE ((ubyte volatile far*)0xf40)
#endif
#ifdef EZ8_UART1
# define Z8_UART1_BASE ((ubyte volatile far*)0xf48)
#endif
/* UART0/1 Status 0 Register Bit Definitions ****************************************/
#define Z8_UARTSTAT0_RDA _HX(80) /* Bit 7: Receive Data Available */
#define Z8_UARTSTAT0_PE _HX(40) /* Bit 6: Parity Error */
#define Z8_UARTSTAT0_OE _HX(20) /* Bit 5: Overrun Error */
#define Z8_UARTSTAT0_FE _HX(10) /* Bit 4: Framing Error */
#define Z8_UARTSTAT0_BRKD _HX(08) /* Bit 3: Break Detect */
#define Z8_UARTSTAT0_TDRE _HX(04) /* Bit 2: Transmitter Data Register Empty */
#define Z8_UARTSTAT0_TXE _HX(02) /* Bit 1: Transmitter Empty */
#define Z8_UARTSTAT0_CTS _HX(01) /* Bit 0: Clear To Send */
/* UART0/1 Control 0/1 Register Bit Definitions *************************************/
#define Z8_UARTCTL0_TEN _HX(80) /* Bit 7: Transmit Enable */
#define Z8_UARTCTL0_REN _HX(40) /* Bit 6: Receive Enable */
#define Z8_UARTCTL0_CTSE _HX(20) /* Bit 5: CTS Enable */
#define Z8_UARTCTL0_PEN _HX(10) /* Bit 4: Parity Enable */
#define Z8_UARTCTL0_PSEL _HX(08) /* Bit 3: Odd Parity Select */
#define Z8_UARTCTL0_SBRK _HX(04) /* Bit 2: Send Break */
#define Z8_UARTCTL0_STOP _HX(02) /* Bit 1: Stop Bit Select */
#define Z8_UARTCTL0_LBEN _HX(01) /* Bit 0: Loopback Enable */
#define Z8_UARTCTL1_MPMD1 _HX(80) /* Bit 7: Multiprocessor Mode (bit1) */
#define Z8_UARTCTL1_MPEN _HX(40) /* Bit 6: Multiprocessor Enable */
#define Z8_UARTCTL1_MPMD0 _HX(20) /* Bit 5: Multiprocessor Mode (bit0) */
#define Z8_UARTCTL1_MPBT _HX(10) /* Bit 4: Multiprocessor Bit Transmit */
#define Z8_UARTCTL1_DEPOL _HX(08) /* Bit 3: Driver Enable Polarity */
#define Z8_UARTCTL1_BRGCTL _HX(04) /* Bit 2: Baud Rate Generator Control */
#define Z8_UARTCTL1_RDAIRQ _HX(02) /* Bit 1: Receive Data Interrupt Enable */
#define Z8_UARTCTL1_IREN _HX(01) /* Bit 0: Infrared Encoder/Decoder Eanble */
/* UART0/1 Mode Status/Select Register Bit Definitions ******************************/
#define Z8_UARTMDSEL_NORMAL _HX(00) /* Bits 5-7=0: Multiprocessor and Normal Mode */
#define Z8_UARTMDSEL_FILTER HX(20) /* Bits 5-7=1: Noise Filter Control/Status */
#define Z8_UARTMDSEL_LINP HX(40) /* Bits 5-7=2: LIN protocol Contol/Status */
#define Z8_UARTMDSEL_HWREV HX(e0) /* Bits 5-7=7: LIN-UART Hardware Revision */
/* Bits 0-4: Mode dependent status */
/* Register access macros ***********************************************************
*
* The register access mechanism provided in ez8.h differs from the useful in other
* NuttX architectures. The following NuttX common macros will at least make the
* access compatible at the source level (however, strict type check is lost).
*/
#ifndef __ASSEMBLY__
# define getreg8(a) (a)
# define putreg8(v,a) (a) = (v)
# define getreg16(a) (a)
# define putreg16(v,a) (a) = (v)
# define getreg32(a) (a)
# define putreg32(v,a) (a) = (v)
#endif /* __ASSEMBLY__ */
/************************************************************************************
* Public Function Prototypes
************************************************************************************/
#ifndef __ASSEMBLY__
#ifdef __cplusplus
#define EXTERN extern "C"
extern "C" {
#else
#define EXTERN extern
#endif
#undef EXTERN
#ifdef __cplusplus
}
#endif
#endif
#endif /* __Z8_CHIP_H */