Merged in fvacek/nuttx (pull request #580)

NUCLEO F432KC typo fixed, correct name is L432KC

Approved-by: Gregory Nutt <gnutt@nuttx.org>

configs/nucleo-l432kc/README.txt

@@ -230,7 +230,7 @@ NuttX EABI "buildroot" Toolchain
 
   1. You must have already configured Nuttx in <some-dir>/nuttx.
 
-     $ tools/configure.sh nucleo-f432kc/nsh
+     $ tools/configure.sh nucleo-l432kc/nsh
      $ make qconfig
      $ V=1 make context all 2>&1 | tee mout
 
@@ -296,13 +296,13 @@ NXFLAT Toolchain
 mbed
 ====
 
-  The Nucleo-F432KC includes boot loader from mbed:
+  The Nucleo-L432KC includes boot loader from mbed:
 
     https://mbed.org/handbook/Homepage
 
   Using the mbed loader:
 
-  1. Connect the Nucleo-F432kc to the host PC using the USB connector.
+  1. Connect the Nucleo-L432kc to the host PC using the USB connector.
   2. A new file system will appear called NUCLEO; open it with Windows
      Explorer (assuming that you are using Windows).
   3. Drag and drop nuttx.bin into the MBED window.  This will load the
@@ -319,7 +319,7 @@ Hardware
 
   LEDs
   ----
-  The Nucleo F401RE and Nucleo F432KC provide a single user LED, LD2.  LD2
+  The Nucleo L432KC provides a single user LED, LD2.  LD2
   is the green LED connected to Arduino signal D13 corresponding to MCU I/O
   PB3 (pin 26).
 
@@ -364,7 +364,7 @@ Serial Consoles
 
   TTL to RS-232 converter connection:
 
-    Nucleo CN10 STM32F432KC
+    Nucleo CN10 STM32L432KC
     ----------- ------------
     Pin 21 PA9  USART1_RX   *Warning you make need to reverse RX/TX on
     Pin 33 PA10 USART1_TX    some RS-232 converters
@@ -396,7 +396,7 @@ Serial Consoles
 
   TTL to RS-232 converter connection:
 
-    Nucleo CN9  STM32F432KC
+    Nucleo CN9  STM32L432KC
     ----------- ------------
     Pin 1  PA3  USART2_RX   *Warning you make need to reverse RX/TX on
     Pin 2  PA2  USART2_TX    some RS-232 converters
@@ -454,7 +454,7 @@ Configurations
   nsh:
   ---------
     Configures the NuttShell (nsh) located at apps/examples/nsh for the
-    Nucleo-F432KC board.  The Configuration enables the serial interfaces
+    Nucleo-L432KC board.  The Configuration enables the serial interfaces
     on UART2.  Support for builtin applications is enabled, but in the base
     configuration no builtin applications are selected (see NOTES below).
 
@@ -481,7 +481,7 @@ Configurations
        Consoles).  I have been using a TTL-to-RS-232 converter connected
        as shown below:
 
-       Nucleo CN10 STM32F432KC
+       Nucleo CN10 STM32L432KC
        ----------- ------------
        Pin 21 PA9  USART1_RX   *Warning you make need to reverse RX/TX on
        Pin 33 PA10 USART1_TX    some RS-232 converters

configs/nucleo-l432kc/include/board.h

@@ -266,4 +266,4 @@ void stm32l4_board_initialize(void);
 #endif
 
 #endif /* __ASSEMBLY__ */
-#endif  /* __CONFIGS_NUCLEO_F432KC_INCLUDE_BOARD_H */
+#endif  /* __CONFIGS_NUCLEO_L432KC_INCLUDE_BOARD_H */