configs/flipnclick-pic32mz: Apply same LED fix as for flipnclick-sam3x. The LED code is cloned.

configs/flipnclick-pic32mz/README.txt

@@ -218,8 +218,8 @@ LEDs and Buttons
     LED_PANIC        The system has crashed  2Hz N/C N/C N/C N/C
     LED_IDLE         MCU is is sleep mode    ---- Not used -----
 
-  Thus if LED L is glowing on and all other LEDs are off (except LED D which
-  was left on but is no longer controlled by NuttX and so may be in any
+  Thus if LED L is glowing faintly and all other LEDs are off (except LED D
+  which was left on but is no longer controlled by NuttX and so may be in any
   state), NuttX has successfully booted and is, apparently, running normally
   and taking interrupts.  If any of LEDs A-D are statically set, then NuttX
   failed to boot and the LED indicates the initialization phase where the

configs/flipnclick-pic32mz/include/board.h

@@ -240,7 +240,7 @@
 #define LED_PANIC        4 /* The system has crashed  2Hz N/C N/C N/C N/C */
 #undef  LED_IDLE           /* MCU is is sleep mode    ---- Not used ----- */
 
-/* Thus if LED L is glowing on and all other LEDs are off (except LED D which
+/* Thus if LED L is faintly glowing and all other LEDs are off (except LED D which
  * was left on but is no longer controlled by NuttX and so may be in any state),
  * NuttX has successfully booted and is, apparently, running normally and taking
  * interrupts.  If any of LEDs A-D are statically set, then NuttX failed to boot

configs/flipnclick-pic32mz/src/pic32mz_autoleds.c

@@ -57,6 +57,7 @@
 /****************************************************************************
  * Pre-processor Definitions
  ****************************************************************************/
+
 /* There are four LEDs on the top, red side of the board.  Only one can be
  * controlled by software:
  *
@@ -89,8 +90,8 @@
  *   LED_PANIC        The system has crashed  2Hz N/C N/C N/C N/C
  *   LED_IDLE         MCU is is sleep mode    ---- Not used -----
  *
- * Thus if LED L is glowing on and all other LEDs are off (except LED D
- * which was left on but is no longer controlled by NuttX and so may be in
+ * Thus if LED L is faintly glowing and all other LEDs are off (except LED
+ * D which was left on but is no longer controlled by NuttX and so may be in
  * any state), NuttX has successfully booted and is, apparently, running
  * normally and taking interrupts.  If any of LEDs A-D are statically set,
  * then NuttX failed to boot and the LED indicates the initialization phase
@@ -122,7 +123,7 @@ static void board_autoled_setone(int ledndx)
   pic32mz_gpiowrite(GPIO_LED_L, ledon[INDEX_LED_L]);
   pic32mz_gpiowrite(GPIO_LED_A, ledon[INDEX_LED_A]);
   pic32mz_gpiowrite(GPIO_LED_B, ledon[INDEX_LED_B]);
-  pic32mz_gpiowrite(GPIO_LED_C, ledon[INDEX_LED_D]);
+  pic32mz_gpiowrite(GPIO_LED_C, ledon[INDEX_LED_C]);
   pic32mz_gpiowrite(GPIO_LED_D, ledon[INDEX_LED_D]);
 }
 
@@ -175,7 +176,7 @@ void board_autoled_on(int led)
         board_autoled_setone(INDEX_LED_B);
         break;
 
-     case 2:
+      case 2:
         board_autoled_setone(INDEX_LED_C);
         break;