Add NSH configuration

git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@3072 42af7a65-404d-4744-a932-0658087f49c3

arch/avr/src/at32uc3/at32uc3_timerisr.c

@@ -126,7 +126,7 @@
 #  define AV32_PSEL 1
 #  define AV32_TOP (82-1)
 #else
-#  define AV32_PSEL 3
+#  define AV32_PSEL 2
 #  define AV32_TOP (144-1)
 #endif
 

arch/avr/src/avr32/up_switchcontext.S

@@ -94,7 +94,7 @@ up_switchcontext:
 	mfsr	r10, AVR32_SR
 	sub		r12, -4*(REG_LR+1)
 
-	/* Then "push" PC=LR, LR, SR, and SP as ther are on entry.                      */
+	/* Then "push" PC=LR, LR, SR, and SP as they are on entry.                      */
 	/*     xx xx xx xx xx xx xx xx SP SR PC LR xx xx xx xx xx                       */
 	/*                             ^r12                                             */
 

configs/avr32dev1/README.txt

@@ -20,6 +20,7 @@ Contents
    - Entering the ISP
    - BatchISP
  * Reset
+ * Make Tip
  * AVR32DEV1 Configuration Options
  * Configurations
 
@@ -229,11 +230,11 @@ AVR32 Bootloader
    verify, read) are performed using these buffers."
  
   The following BatchISP command line will erase FLASH, write the nuttx binary
-  into FLASH, and reset the AVR32.  This command line is availabel in the
+  into FLASH, and reset the AVR32.  This command line is available in the
   script config/avr32dev1/tools/doisp.sh:
 
      batchisp -device at32uc3b0256 -hardware usb -operation erase f memory flash \
-     blankcheck loadbuffer nuttx program verify start reset 0
+     blankcheck loadbuffer nuttx.elf program verify start reset 0
 
   "BatchISP main commands available on AT32UC3xxxxx are:
   
@@ -289,10 +290,23 @@ AVR32 Bootloader
 Reset
 ^^^^^
 
-   The AVR32DEV1 reset button is not useful for restarting the program.  It
-   seems that, after the reset, the RTC is left is a bad state and is constantly
-   busy (this might be the fault of the bootloader???).  There does not seem
-   to be any way around this except for power cycling the board.
+   I don't trust the reset button -- if you reset and something weird happens,
+   try a full power cycle.
+
+Make Tip
+^^^^^^^^
+
+   Because this build uses a native Windows toolchain and the native Windows
+   does not understand Cygwin/POSIX paths, the NuttX make sysem does something
+   weird:  It copies the configuration directories instead of simply linking
+   to them (it could, perhaps, use the NTFS mklink command, but it doesn't).
+
+   A consequence of this is that you can easily get confused and get editting
+   a file in one of the linked directories, re-build, and not see your changes.
+   To work around this annoying behavior, I also do the following when I make:
+   
+   make clean_context all <-- Remove and re-copy all of the directories, then make all
+   doisp.sh               <-- Load the code onto the board.
 
 AVR32DEV1 Configuration Options
 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
@@ -410,6 +424,10 @@ sudirectory and can be selected as follow:
 
 Where <subdir> is one of the following:
 
+  nsh:
+    Configures the NuttShell (nsh) located at examples/nsh.  The
+    Configuration enables only the serial NSH interface.
+
   ostest:
     This configuration directory, performs a simple OS test using
     examples/ostest.

configs/avr32dev1/nsh/Make.defs

+############################################################################
+# configs/avr32dev1/nsh/Make.defs
+#
+#   Copyright (C) 2010 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <spudmonkey@racsa.co.cr>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+include ${TOPDIR}/.config
+
+# Setup for the selected toolchain
+
+ifeq ($(CONFIG_AVR32_AVRTOOLSW),y)
+  # AVR Tools under Windows
+  CROSSDEV = avr32-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mpart=uc3b0256
+endif
+ifeq ($(CONFIG_AVR32_AVRTOOLSL),y)
+  # AVR Tools under Linux
+  CROSSDEV = avr32-
+  ARCHCPUFLAGS = -mpart=uc3b0256
+endif
+
+ifeq ($(WINTOOL),y)
+  # Windows-native toolchains
+  DIRLINK = $(TOPDIR)/tools/winlink.sh
+  DIRUNLINK = $(TOPDIR)/tools/unlink.sh
+  MKDEP = $(TOPDIR)/tools/mknulldeps.sh
+  ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
+  ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
+  ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nsh/ld.script}"
+else
+  # Linux/Cygwin-native toolchain 
+  MKDEP = $(TOPDIR)/tools/mkdeps.sh
+  ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
+  ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
+  ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nsh/ld.script
+endif
+
+CC = $(CROSSDEV)gcc
+CXX = $(CROSSDEV)g++
+CPP = $(CROSSDEV)gcc -E
+LD = $(CROSSDEV)ld
+AR = $(CROSSDEV)ar rcs
+NM = $(CROSSDEV)nm
+OBJCOPY = $(CROSSDEV)objcopy
+OBJDUMP = $(CROSSDEV)objdump
+
+ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
+ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
+
+ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
+  ARCHOPTIMIZATION = -g
+else
+  ARCHOPTIMIZATION = -Os -ffunction-sections -fdata-sections -fno-strict-aliasing
+endif
+
+ARCHCFLAGS = -fno-builtin -muse-rodata-section
+ARCHCXXFLAGS = -fno-builtin -fno-exceptions
+ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
+ARCHWARNINGSXX = -Wall -Wshadow
+ARCHDEFINES =
+ARCHNOPICFLAGS = -fno-pic
+ARCHPICFLAGS = -fpic
+ARCHALLCFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) -pipe
+ARCHALLCXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) -pipe
+
+CFLAGS = $(ARCHNOPICFLAGS) $(ARCHALLCFLAGS)
+CPICFLAGS = $(ARCHPICFLAGS) $(ARCHALLCFLAGS)
+CXXFLAGS = $(ARCHNOPICFLAGS) $(ARCHALLCXXFLAGS)
+CXXPICFLAGS = $(ARCHPICFLAGS) $(ARCHALLCXXFLAGS)
+CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES)
+AFLAGS = $(ARCHALLCFLAGS) -D__ASSEMBLY__
+
+OBJEXT = .o
+LIBEXT = .a
+EXEEXT =
+
+LDFLAGS += -nostartfiles -nodefaultlibs
+ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
+  LDFLAGS += -g
+endif
+
+define PREPROCESS
+	@echo "CPP: $1->$2"
+	@$(CPP) $(CPPFLAGS) $1 -o $2
+endef
+
+define COMPILE
+	@echo "CC: $1"
+	@$(CC) -c $(CFLAGS) $1 -o $2
+endef
+
+define COMPILEXX
+	@echo "CXX: $1"
+	@$(CXX) -c $(CXXFLAGS) $1 -o $2
+endef
+
+define ASSEMBLE
+	@echo "AS: $1"
+	@$(CC) -c $(AFLAGS) $1 -o $2
+endef
+
+define ARCHIVE
+	echo "AR: $2"; \
+	$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
+endef
+
+define CLEAN
+	@rm -f *.o *.a
+endef
+
+HOSTCC = gcc
+HOSTINCLUDES = -I.
+HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
+HOSTLDFLAGS =
+

configs/avr32dev1/nsh/ld.script

+/****************************************************************************
+ * configs/avr32dev1/nsh/ld.script
+ *
+ *   Copyright (C) 2010 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <spudmonkey@racsa.co.cr>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+OUTPUT_FORMAT("elf32-avr32", "elf32-avr32", "elf32-avr32")
+OUTPUT_ARCH(avr32:uc)
+ENTRY(_stext)
+
+/* The following assumes that the bootloader resides at 0x8000:0000 and so
+ * links the application to execute after the bootloader at 0x8000:2000.
+ * To link so that NuttX boots directly without using the bootloader,
+ * change the flash definition to:
+ *
+ *   flash (rxai!w)  : ORIGIN = 0x80000000, LENGTH = 256K
+ */
+
+MEMORY
+{
+    flash (rxai!w)  : ORIGIN = 0x80002000, LENGTH = 256K - 8K
+    intram (wxa!ri) : ORIGIN = 0x00000004, LENGTH = 32K
+    userpage        : ORIGIN = 0x80800000, LENGTH = 512
+    factorypage     : ORIGIN = 0x80800200, LENGTH = 512
+}
+
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		*(.text .text.*)        
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)        
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+	} > flash
+
+	_eronly = ABSOLUTE(.);		/* See below                    */
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > intram AT > flash
+
+	.bss : {			/* BSS				*/
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		_ebss = ABSOLUTE(.);
+	} > intram
+					/* Stabs debugging sections.	*/
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}
+

configs/avr32dev1/nsh/setenv.sh

+#!/bin/bash
+# configs/avr32dev1/nsh/setenv.sh
+#
+#   Copyright (C) 2010 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <spudmonkey@racsa.co.cr>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+
+if [ "$(basename $0)" = "setenv.sh" ] ; then
+  echo "You must source this script, not run it!" 1>&2
+  exit 1
+fi
+
+#
+# This PATH setup assumes that you are using versin 2.1.4 of the Atmel
+# AVR GNU tools installed at the default location on Windows.  NOTE
+# that the path is in appended to the end of the PATH variable; this is
+# because there are also many GNUWin32 binaries there that conflict with
+# Cygwin versions.
+#
+
+if [ -z "${PATH_ORIG}" ]; then export PATH_ORIG="${PATH}"; fi
+
+WD=`pwd`
+
+export AVR32_BIN="/cygdrive/c/Program Files/Atmel/AVR Tools/AVR32 Toolchain/bin/"
+export FLIP_BIN="/cygdrive/c/Program Files/Atmel/Flip 3.4.2/bin"
+export AVR32DEV1_BIN="${WD}/configs/avr32dev1/tools"
+export PATH="${FLIP_BIN}:${AVR32DEV1_BIN}:/sbin:/usr/sbin:${PATH_ORIG}:${AVR32_BIN}"
+
+echo "PATH : ${PATH}"

configs/avr32dev1/ostest/defconfig

@@ -311,12 +311,12 @@ CONFIG_DEBUG_VERBOSE=n
 CONFIG_DEBUG_SYMBOLS=n
 CONFIG_MM_REGIONS=1
 CONFIG_ARCH_LOWPUTC=y
-CONFIG_RR_INTERVAL=200
+CONFIG_RR_INTERVAL=0
 CONFIG_SCHED_INSTRUMENTATION=n
 CONFIG_TASK_NAME_SIZE=0
 CONFIG_START_YEAR=2010
-CONFIG_START_MONTH=6
-CONFIG_START_DAY=20
+CONFIG_START_MONTH=11
+CONFIG_START_DAY=2
 CONFIG_GREGORIAN_TIME=n
 CONFIG_JULIAN_TIME=n
 CONFIG_DEV_CONSOLE=y
@@ -668,7 +668,7 @@ CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1)
 # Settings for examples/ostest
 #
 CONFIG_EXAMPLES_OSTEST_LOOPS=1
-CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
+CONFIG_EXAMPLES_OSTEST_STACKSIZE=1024
 CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
 
 #