drivers/usbdev/cdcacm.c:  Add a failsafe time to assure that the RX pending queue cannot stall indefinitely.  I can imagine a corner case where the serial driver's RX buffer is full and it stops accepting data and where all of the read requests are queued and there is not event to restart RX processing.  I am not sure that that scenario can really happen, but the failsafe timer gives me peace of mind.

    drivers/usbdev/cdcacm.c:  Change design for queuing RX packets that cannot be processed.  Previous design had a logic problem that could cause data loss.

    drivers/usbdev/cdcacm:  Fixes one of two know design issues.

    drivers/usbdev/cdcacm:  First attempt to plug data leak in input flow control design.  Still missing a few things.

    net/socket/recvfrom.c: Check fromlen integrity before using it.

    net/socket/net_sockets.c: Always check for valid psock before using.

    net/tcp/tcp_send_unbuffered.c:  Avoid using psock beforing checking its integrity.

    sched/timer/timer_create.c: Fix watchdog resource leak if cannot allocate a new timer.

drivers/net/rndis.c:  Eliminate a warning when assertions disabled. Consequence of replacing assert() with DEBUGASSERT().

drivers/usbdev/rindis.c:  Change some naming to conform with coding standard.  Use DEBUGASSERT vs. assert so that the assertions can be disabled.

From: Sakari Kapanen <sakari.kapanen@optofidelity.com>
Date: Sun, 24 Sep 2017 13:19:25 +0300
Subject: [PATCH] ICMPv6: fix router advertisement

Fixes several errors preventing icmpv6_radvertise.c from being compiled. Fixes conversions to network byte order (namely vlifetime, plifetime, mtu).

IPv6 source address is set to link-local IP address instead of the address in the netdev structure. This is in compliance to RFC 4861. RA didn't work on Linux before this change.

Finally, router prefix and prefix length are derived from the IPv6 address and netmask in the netdev structure. This seems to make more sense than using a predefined, separate prefix from the config.

drivers/usbdev:  CDC/ACM should reset all 'irregular' notifications to zero after sending the SerialState packet.

include/nuttx/net/net.h:  Add missing semicolon in prototype.  Fixes error in certain combinations of configuration options.

stm32:stm32f40xxx I2C ensure proper isr handling

Injecting data errors that causes a STOP to be perceived by the
   driver, will continually re-enter the isr with SB not set and BTF
   and RxNE set.  This changes allows the interrupts to
   be cleared and  propagates a I2C_SR1_TIMEOUT to the waiting task.

Approved-by: Gregory Nutt <gnutt@nuttx.org>

In some cases, packets are still not sent behind the router. I found that NuttX sends the ARP requests not to the router but to the target. Mistake in file net/route/netdev_router.c.  From Aleksandr Kazantsev

STM32L4 ADC, DFSDM: add routing of ADC data to DFSDM filters

* configs/nucleo-l496zg: add DFSDM initialization

* STM32L4 ADC: add option for routing ADC data to DFSDM, fix DFSDM DMA

Approved-by: Gregory Nutt <gnutt@nuttx.org>

Networking: drivers/net/loopback.c: Eliminate a warning.  net/netdev/netdev_ifconfig.c: Was not returning all of the address info.

    Networking:  Add implementation of logic for SIOCGIFCONF and SIOCGLIFCOF IOCTL commnds.
    Networking:  Add definitions and stuctures to support SIOCGIFCONF and SIOCGLIFCONF IOCTL commands.

viewtool-stm32f107:  Replace old stm32_appinit.c (now stm32_bringup.c) with 'standard' stm32_appinit.c from the STM32F4-Discovery.  Add CONFIG_BOARD_INITIALIZE logic to stm32_boot.c

STM32L4 DFSDM: add peripheral, DAC, TIM: small changes

* STM32L4 DAC: do not configure output pin if it is not used

* STM32L4 TIM: fix compilation of timers with complementary outputs when not PWM_MULTICHAN

* STM32L4 DFSDM: peripheral for digital filters for sigma-delta ADCs

    Initial version. Timer trigger support is not completed and there is
    some issue with DMA.

Approved-by: Gregory Nutt <gnutt@nuttx.org>

sched/env_dup.c:  Fix an error in the duplication of the child tasks environment in the special case where the parent's environment was created, but then all of the variables were unset.  In that case, there is still an allocation in place but the size of the allocation is zero.  This case was not being handled correctly when a child task attempts to create its environment and inherit the zero-size partent environment.  Noted by Anthony Merlino.