drivers/lcd/ft80x:  Fix a typo that caused the driver to fail to recognize the ft801 chip version. Also update an unrelated README file.

    drviers/lcd/ft80x:  No longer depends on CONFIG_EXPERIMENTAL
    Update README.txt

    drivers/lcd/ft80x:  ACTIVE host command appears to be formatted differently than other host commands; Fix ROM CHIPID.  Appears to be big-ending, BCD.
    drivers/lcd/ft80x:  Fix some compile issues when debug features are enabled.

drivers/net/phy_notify.c:  Use phy debug macros instead of net debug macros.  ninfo() and nerr() are used a bit too much, so the console output is difficult to read with network debug.

Feature pca9540bdp i2cmultiplexer

* Implement common i2c multiplexer abstraction to be reused by i2c multiplexer devices. Provide common interface with transfer and reset calls to set up virtual i2c busses.

* Remove i2cmux_lower_half.c and headers, will be implemented by each mux driver

* Implement PCA9540BDP I2C multiplexer lower half which uses the common i2c mux abstraction

* Remove application interface and implement common i2c functions

* Remove application interface from pca driver and implement common i2c functions directly in the pca driver

* Use i2cerr

Approved-by: Gregory Nutt <gnutt@nuttx.org>

Per OpenGroup.org, syslog -- and, hence, nonstandard vsyslog, and debug wrappers -- does not return a value.  Rename _vsyslog to nx_vsyslog.  Use internal nx_vsyslog in the few cases where a return value is required.

Fix some errors found in build testing + clean-up some issues with last changes to remove use of printf() from within the OS.

Remove all usage of printf() from the OS.  That is not an acceptable context for the use of an application-oriented interface that depends on a task-specific file descriptor and C buffered I/O.

drivers/wireless/cc1101.c:  Fix a few things that I bungled in my review of the driver mods.  Fix the logic that was dumping register contents: printf() may not be used within the OS and the syslog and debug macros may add ornamentatino to the output.  The only real option inside the OS is to buffer the data and outputing with a single syslog write (vs. many tiny writes).

    cc1101:  Changes from review of last PR.
    remove gpio
    remove  cc1101 frame len
    remove FLAGS_RXONLY flags
    add cc1101 function
    remove some waring
    add cc1101 poll function
    add cc1101 register
    add cc1101 isr read data
    add cc1101 spi deviceId
    add cc1101 init2
    add wait cc1101 chip ready
    raw init cc1101

drivers/i2c and drivers/spi:  Fix compile if CONFIG_DISABLE_PSEUDOFS_OPERATIONS, fix bad NULL checks

drivers/lcd:  Add FT80x controls for the case where the audio amplifier is controlled by FT80x GPIOs vs MCU gpios.

configs/viewtool-stm32f107:  Add support for FT80X initialization.  Add ft80x configuration that will eventually be used for testing the ft80x if I ever receive hardware.

    drivers/lcd:  Add an IOcTL to FT80x driver to write to FIFO CMD RAM.

Added ECANCELED condition to DEBUGASSERT-s checking sem_wait result

Approved-by: Gregory Nutt <gnutt@nuttx.org>

Author: Juha Niskanen <juha.niskanen@haltian.com>
Date:   Mon Feb 19 15:03:17 2018 -0600

    drivers/mtd:  mtd_config.c:  Add still more error handling (to detect bad underlying flash implementations)
    drivers/mtd:  mtd_config.c:  Remove MTD_ERASE that was erasing data block instead of erase block.  This is a partial revert of 4f18b4.  Reported-by: Pascal Speck <iktek01@yahoo.com>
    arch/arm/src/stm32l4:  stm32l4_flash: change flash programming to use page buffer for unaligned writes.

    drivers/lcd and include/nuttx/lcd:  Add FT80x support for writing to graphics memory.  Also add some definitions needed by apps/examples/ft80x for bitmap manipulation.
    drivers/lcd:  Review/update FT80x initializatin logic

drivers/lcd: Detect and handle more errors in return values within the LCD framebuffer and SSD1306 drivers

drivers/lcd:  In order to actually use the new register access IOCTL calls, need to move the register address definitions out of the private header file and into the public header file.

    drivers/lcd:  Rename ft80x_base.c to just ft80x.c.  Add logic to notify FT80X clients of events via signals.
    drivers/lcd:  Trivial updates to naming.  Add some new definitions.