Newer
Older
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
#!/bin/bash
LANG=C
ENVBOX=./pybox
DEVICE=/dev/serial/by-id/usb-STMicroelectronics_STM32_Virtual_ComPort_in_FS_Mode_00000000050C-if00
#need sudo apt-get install lm-sensors
reset
VERT="\\033[1;32m"
NORMAL="\\033[0;39m"
ROUGE="\\033[1;31m"
ROSE="\\033[1;35m"
BLEU="\\033[1;34m"
BLANC="\\033[0;02m"
BLANCLAIR="\\033[1;08m"
JAUNE="\\033[1;33m"
CYAN="\\033[1;36m"
echo ""
echo -e "\t\t---=== System ===---"
echo "[ Software ] :" `$ENVBOX -d $DEVICE SoftwareType` " Rev. " `$ENVBOX -d $DEVICE SoftwareRevision`
TS=$(echo "`$ENVBOX -d $DEVICE Uptime`/1000" | bc -l )
TSday=$(echo "`$ENVBOX -d $DEVICE Uptime`/86400000 " | bc -l)
echo "[ Uptime ] : " $(printf "%d" ${TSday/.*}) "day(s)"
echo "[ Uptime ] : " $( date -ud @$TS | awk '{print $4}')
echo "[ Dock ] : " `$ENVBOX -d $DEVICE Switch1 Status`
echo
echo -e "\t\t---=== Power ===---"
echo "[ Voltage ] : " $(printf "%.1f" `$ENVBOX -d $DEVICE LineVoltage`)"V"
echo "[ Current ] : " $(printf "%.1f" `$ENVBOX -d $DEVICE LineCurrent`)"A"
echo
echo -e "\t\t---=== Backlight ===---"
echo
echo "[ Name ] : " `$ENVBOX -d $DEVICE Backlight1 Name`
echo "[ Mode ] : " `$ENVBOX -d $DEVICE Backlight1 Mode`
echo "[ Enable ] : " `$ENVBOX -d $DEVICE Backlight1 Enable`
echo "[ Enabled ] : " `$ENVBOX -d $DEVICE Backlight1 Enabled`
echo "[ Thermal Protection ] : " `$ENVBOX -d $DEVICE Backlight1 Protection`
echo
echo -e "\t\t---=== Temperatures ===---"
echo "[ Envbox ] : " $(printf "%.1f" `$ENVBOX -d $DEVICE Temperature1 Temp`)"°C"
echo "[ T alim1 ] : " $(printf "%.1f" `$ENVBOX -d $DEVICE Temperature2 Temp`)"°C"
echo "[ T alim2 ] : " $(printf "%.1f" `$ENVBOX -d $DEVICE Temperature3 Temp`)"°C"
echo
echo "[ T upscale ] : " $(printf "%.1f" `$ENVBOX -d $DEVICE Temperature5 Temp`)"°C"
echo
echo -e "\t\t---=== FAN A ===---"
echo "[ Mode ] : " `$ENVBOX -d $DEVICE Fan1 Mode`
echo "[ Command ] : " $(printf "%.1f" `$ENVBOX -d $DEVICE Fan1 PWM`)"%"
echo "[ Tachy ] : " $(printf "%.1f" `$ENVBOX -d $DEVICE Fan1 RPM`)"rpm"
echo -e "\t\t---=== FAN B ===---"
echo
echo "[ Mode ] : " `$ENVBOX -d $DEVICE Fan2 Mode`
echo "[ Command ] : " $(printf "%.1f" `$ENVBOX -d $DEVICE Fan2 PWM`)"%"
echo "[ Tachy ] : " $(printf "%.1f" `$ENVBOX -d $DEVICE Fan2 RPM`)"rpm"